Troubleshooting • Re: RPi5 Bootloader Update Error

Code:

Type [C-a] [C-h] to see available commandsTerminal ready  3.92 RPi: RECOVERY release VERSION:000d3ca2 DATE: 2025/08/27 TIME: 20:01:47  3.92 BOOTMODE: 0x07 partition 0 build-ts BUILD_TIMESTAMP=1756321307 serial cf536143 boardrev d04170 stc 3928772  3.93 AON_RESET: 00000003 PM_RSTS 00001000  3.94 POWER_OFF_ON_HALT: 0 WAIT_FOR_POWER_BUTTON 0 power-on-reset 1  3.99 BOOT_ORDER: 0xf3  3.99 USB-OTG disconnect  6.07 Read config.txt bytes      378 hnd 0x0  6.65 pieeprom.sig  6.65 hash: cf97dac22dbf34859234935695db3e9b7d5dcd95acc8f52996fdaf68bd87ecb4  6.65 ts: 1757789907  7.03 Reading EEPROM: 2097152 bytes 0xc1160000  9.08 2504ms 10.56 Writing EEPROM+ 10.56 EEPROM ERROR sector-erase: 0x0 0x0 10.59 Update failed. Retrying. 10.62 Erasing EEPROM 10.64 EEPROM error chip-erase: 0x0 0 10.46 BOOT_ORDER: 0xf3 10.89 Read config.txt bytes      378 hnd 0x0 10.61 USB-OTG disconnect 10.18 RECOVERY: COMPLETE: REBOOT 0

Code:

ubuntu@ubuntu:~$ sudo picocom -b 115200 /dev/ttyACM0 picocom v3.1port is        : /dev/ttyACM0flowcontrol    : nonebaudrate is    : 115200parity is      : nonedatabits are   : 8stopbits are   : 1escape is      : C-alocal echo is  : nonoinit is      : nonoreset is     : nohangup is      : nonolock is      : nosend_cmd is    : sz -vvreceive_cmd is : rz -vv -Eimap is        : omap is        : emap is        : crcrlf,delbs,logfile is     : noneinitstring     : noneexit_after is  : not setexit is        : noType [C-a] [C-h] to see available commandsTerminal ready  3.79 RPi: BOOTSYS release VERSION:d179f03a DATE: 2025/09/08 TIME: 15:51:58  3.80 BOOTMODE: 0x07 partition 0 build-ts BUILD_TIMESTAMP=1757343118 serial cf536143 boardrev d04170 stc 3802582  3.81 AON_RESET: 00000003 PM_RSTS 00001000  3.81 POWER_OFF_ON_HALT: 0 WAIT_FOR_POWER_BUTTON 0 power-on-reset 1  3.82 RP1_BOOT chip ID: 0x20001927  3.83 PCIEx1: PWR 0 DET_WAKE 0  3.83 part 00000000 reset_info 00000000  3.83 PMIC reset-event 00000000 rtc 00000003 alarm 00000000 enabled 0  3.84 uSD voltage 3.3V  3.84 USB-OTG disconnect  6.55 Initialising SDRAM rank 2 total-size: 64 Gbit 4267 (0x14 0x00)  6.56 DDR 4267 1 0 64 152 BL:1  8.45 OTP boardrev d04170 bootrom a a  8.46 Customer key hash 0000000000000000000000000000000000000000000000000000000000000000  8.46 VC-JTAG unlocked  8.49 RP1_BOOT chip ID: 0x20001927  8.81 RP1_BOOT chip ID: 0x20001927  8.81 RP1_BOOT: fw size 46888  9.45 PCI2 init  9.45 PCI2 reset  9.49 PCIe scan 00001de4:00000001  9.50 RP1_CHIP_INFO 20001927  9.50 RPi: RPIBOOT release VERSION:d179f03a DATE: 2025/09/08 TIME: 15:51:58  9.50 BOOTMODE: 0x07 partition 0 build-ts BUILD_TIMESTAMP=1757343118 serial cf536143 boardrev d04170 stc 9509477  9.54 usb_pd_init status 3  9.54 USB_PD CONFIG 0 41  9.58 SD_OC: 0  9.86 Boot mode: RPIBOOT (03) order f  9.09 Read config.txt bytes      238 hnd 0x0  9.11 Loading boot.img ... 11.28 Read boot.img bytes 29360640 hnd 0x0 11.12 MBR: 0x00000001,   57344 type: 0x0c 11.13 MBR: 0x00000000,       0 type: 0x00 11.13 MBR: 0x00000000,       0 type: 0x00 11.14 MBR: 0x00000000,       0 type: 0x00 11.45 Trying partition: 0 11.47 type: 16 lba: 1 'mkfs.fat' '  V       ^ ' clusters 14299 (4) 11.15 rsc 4 fat-sectors 56 root dir cluster 1 sectors 32 entries 512 11.15 FAT16 clusters 14299 11.63 Read config.txt bytes      363 hnd 0x210 11.16 [ramdisk] pieeprom.upd not found 11.70 usb_max_current_enable default 0 max-current 3000 11.76 Read bcm2712-rpi-5-b.dtb bytes    78723 hnd 0xd7 11.18 dt-match: compatible: raspberrypi,5-model-b match: brcm,bcm2712 11.18 dt-match: compatible: brcm,bcm2712 match: brcm,bcm2712 11.01 Selecting USB low current limit 11.20 MESS:00:00:11.204344:0: *** Restart logging 11.07 Read /config.txt bytes      363 hnd 0x210 11.11 Read /config.txt bytes      363 hnd 0x210 11.21 MESS:00:00:11.218558:0: Initial voltage 800000 temp 26289 11.41 MESS:00:00:11.419116:0: avs_2712: AVS pred 8828 882800 temp 26289 11.42 MESS:00:00:11.422718:0: vpred 882 mV +0 11.43 MESS:00:00:11.431352:0: FB framebuffer_swap 1 11.43 MESS:00:00:11.434669:0: Select resolution HDMI0/2 hotplug 0 max_mode 2 11.44 MESS:00:00:11.440107:0: Select resolution HDMI1/2 hotplug 0 max_mode 2 11.44 Loading 'rootfs.cpio.zst' to 0x00000000 offset 0x0 11.05 Read rootfs.cpio.zst bytes 17352765 hnd 0x14cf 11.69 MESS:00:00:11.692211:0: initramfs (rootfs.cpio.zst) loaded to 0x2df73000 (size 0x108c83d) 11.69 MESS:00:00:11.697989:0: dtb_file 'bcm2712-rpi-5-b.dtb' 11.70 Loading 'bcm2712-rpi-5-b.dtb' to 0x00000000 offset 0x100 11.09 Read bcm2712-rpi-5-b.dtb bytes    78723 hnd 0xd7 11.36 Read /overlays/overlay_map.dtb bytes     5887 hnd 0x7a5 11.76 PCIEx1: PWR 0 DET_WAKE 0 11.77 Customer public key not loaded. 11.78 Read /config.txt bytes      363 hnd 0x210 11.85 Read /overlays/dwc2.dtbo bytes      801 hnd 0x7d3 11.79 MESS:00:00:11.797693:0: Loaded overlay 'dwc2' 11.79 MESS:00:00:11.799556:0: dtparam: dr_mode=peripheral 11.80 MESS:00:00:11.805005:0: dtparam: pciex1=true 11.98 Read /cmdline.txt bytes       71 hnd 0x20f 11.90 MESS:00:00:11.900181:0: Read command line from file 'cmdline.txt': 11.90 MESS:00:00:11.906692:0: 'rootwait console=tty1 console=serial0,115200 root=/dev/ram0 loglevel=8' 12.09 MESS:00:00:12.094463:0: RPM 116, max RPM 169 12.15 BMD "armstub8-2712.bin" not found 12.56 fs_open: 'armstub8-2712.bin'  12.16 Loading 'kernel8.img' to 0x00000000 offset 0x200000 12.20 Read kernel8.img bytes  6293697 hnd 0x8cd 13.03 MESS:00:00:13.039274:0: Device tree loaded to 0x2df5f600 (size 0x139e7) 13.04 PCI1 reset 13.05 PCI2 reset 13.07 USB-OTG disconnect 13.07 set_reboot_order 0 13.07 set_reboot_arg1 0 13.07 USB-OTG disconnect 13.11 MESS:00:00:13.116905:0: Starting OS 13116 ms 13.12 MESS:00:00:13.121309:0: 00000040: -> 00000480 13.12 MESS:00:00:13.123403:0: 00000030: -> 00100080 13.12 MESS:00:00:13.128115:0: 00000034: -> 00100080 13.13 MESS:00:00:13.132828:0: 00000038: -> 00100080 13.13 MESS:00:00:13.137541:0: 0000003c: -> 00100080NOTICE:  BL31: v2.6(release):v2.6-240-gfc45bc492NOTICE:  BL31: Built : 12:55:13, Dec  4 2024[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x414fd0b1][    0.000000] Linux version 6.12.42-v8 (tim@buildbot) (aarch64-buildroot-linux-gnu-gcc.br_real (Buildroot 2024.11.3-21-gfcd57a30c1) 13.3.0, GNU ld (GNU Binutils) 2.42) #1 SMP PREEMPT Thu Aug 21 12:06:01 BST 2025[    0.000000] KASLR enabled[    0.000000] random: crng init done[    0.000000] Machine model: Raspberry Pi 5 Model B Rev 1.0[    0.000000] efi: UEFI not found.[    0.000000] Reserved memory: created CMA memory pool at 0x000000003bc00000, size 64 MiB[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool[    0.000000] OF: reserved mem: 0x000000003bc00000..0x000000003fbfffff (65536 KiB) map reusable linux,cma[    0.000000] OF: reserved mem: 0x0000000000000000..0x000000000007ffff (512 KiB) nomap non-reusable atf@0[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000001ffffffff][    0.000000] Faking node 0 at [mem 0x0000000000000000-0x000000003fffffff] (1024MB)[    0.000000] Faking node 1 at [mem 0x0000000040000000-0x000000007fffffff] (1024MB)[    0.000000] Faking node 2 at [mem 0x0000000080000000-0x00000000bfffffff] (1024MB)[    0.000000] Faking node 3 at [mem 0x00000000c0000000-0x00000000ffffffff] (1024MB)[    0.000000] Faking node 4 at [mem 0x0000000100000000-0x000000013fffffff] (1024MB)[    0.000000] Faking node 5 at [mem 0x0000000140000000-0x000000017fffffff] (1024MB)[    0.000000] Faking node 6 at [mem 0x0000000180000000-0x00000001bfffffff] (1024MB)[    0.000000] Faking node 7 at [mem 0x00000001c0000000-0x00000001ffffffff] (1024MB)[    0.000000] NUMA: Initialized distance table, cnt=8[    0.000000] NODE_DATA(0) allocated [mem 0x3bbfd300-0x3bbfffff][    0.000000] NODE_DATA(1) allocated [mem 0x7fffd300-0x7fffffff][    0.000000] NODE_DATA(2) allocated [mem 0xbfffd300-0xbfffffff][    0.000000] NODE_DATA(3) allocated [mem 0xffffd300-0xffffffff][    0.000000] NODE_DATA(4) allocated [mem 0x13fffd300-0x13fffffff][    0.000000] NODE_DATA(5) allocated [mem 0x17fffd300-0x17fffffff][    0.000000] NODE_DATA(6) allocated [mem 0x1bfffd300-0x1bfffffff][    0.000000] NODE_DATA(7) allocated [mem 0x1fef9e300-0x1fefa0fff][    0.000000] Zone ranges:[    0.000000]   DMA      [mem 0x0000000000000000-0x00000000ffffffff][    0.000000]   DMA32    empty[    0.000000]   Normal   [mem 0x0000000100000000-0x00000001ffffffff][    0.000000] Movable zone start for each node[    0.000000] Early memory node ranges[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000007ffff][    0.000000]   node   0: [mem 0x0000000000080000-0x000000003fbfffff][    0.000000]   node   1: [mem 0x0000000040000000-0x000000007fffffff][    0.000000]   node   2: [mem 0x0000000080000000-0x00000000bfffffff][    0.000000]   node   3: [mem 0x00000000c0000000-0x00000000ffffffff][    0.000000]   node   4: [mem 0x0000000100000000-0x000000013fffffff][    0.000000]   node   5: [mem 0x0000000140000000-0x000000017fffffff][    0.000000]   node   6: [mem 0x0000000180000000-0x00000001bfffffff][    0.000000]   node   7: [mem 0x00000001c0000000-0x00000001ffffffff][    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fbfffff][    0.000000] Initmem setup node 1 [mem 0x0000000040000000-0x000000007fffffff][    0.000000] Initmem setup node 2 [mem 0x0000000080000000-0x00000000bfffffff][    0.000000] Initmem setup node 3 [mem 0x00000000c0000000-0x00000000ffffffff][    0.000000] Initmem setup node 4 [mem 0x0000000100000000-0x000000013fffffff][    0.000000] Initmem setup node 5 [mem 0x0000000140000000-0x000000017fffffff][    0.000000] Initmem setup node 6 [mem 0x0000000180000000-0x00000001bfffffff][    0.000000] Initmem setup node 7 [mem 0x00000001c0000000-0x00000001ffffffff][    0.000000] On node 1, zone DMA: 1024 pages in unavailable ranges[    0.000000] psci: probing for conduit method from DT.[    0.000000] psci: PSCIv1.1 detected in firmware.[    0.000000] psci: Using standard PSCI v0.2 function IDs[    0.000000] psci: MIGRATE_INFO_TYPE not supported.[    0.000000] psci: SMC Calling Convention v1.2[    0.000000] percpu: Embedded 22 pages/cpu s49752 r8192 d32168 u90112[    0.000000] pcpu-alloc: s49752 r8192 d32168 u90112 alloc=22*4096[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [    0.000000] Detected PIPT I-cache on CPU0[    0.000000] CPU features: detected: Virtualization Host Extensions[    0.000000] CPU features: detected: Spectre-v4[    0.000000] CPU features: detected: Spectre-BHB[    0.000000] CPU features: kernel page table isolation forced ON by KASLR[    0.000000] CPU features: detected: Kernel page table isolation (KPTI)[    0.000000] CPU features: detected: SSBS not fully self-synchronizing[    0.000000] alternatives: applying boot alternatives[    0.000000] Kernel command line: reboot=w coherent_pool=1M 8250.nr_uarts=1 pci=pcie_bus_safe cgroup_disable=memory numa_policy=interleave nvme.max_host_mem_size_mb=0 bcm2708_fb.fbwidth=640 bcm2708_fb.fbheight=480 bcm2708_fb.fbdepth=16 bcm2708_fb.fbswap=1 numa=fake=8 system_heap.max_order=0 smsc95xx.macaddr=D8:3A:DD:D4:FF:EC vc_mem.mem_base=0x3fc00000 vc_mem.mem_size=0x40000000  rootwait console=tty1 console=ttyAMA10,115200 root=/dev/ram0 loglevel=8[    0.000000] cgroup: Disabling memory control group subsystem[    0.000000] mempolicy: NUMA default policy overridden to 'interleave:0-7'[    0.000000] Fallback order for Node 0: 0 1 2 3 4 5 6 7 [    0.000000] Fallback order for Node 1: 1 2 3 4 5 6 7 0 [    0.000000] Fallback order for Node 2: 2 3 4 5 6 7 0 1 [    0.000000] Fallback order for Node 3: 3 4 5 6 7 0 1 2 [    0.000000] Fallback order for Node 4: 4 5 6 7 0 1 2 3 [    0.000000] Fallback order for Node 5: 5 6 7 0 1 2 3 4 [    0.000000] Fallback order for Node 6: 6 7 0 1 2 3 4 5 [    0.000000] Fallback order for Node 7: 7 0 1 2 3 4 5 6 [    0.000000] Built 8 zonelists, mobility grouping on.  Total pages: 2096128[    0.000000] Policy zone: Normal[    0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off[    0.000000] software IO TLB: area num 4.[    0.000000] software IO TLB: mapped [mem 0x00000000fae00000-0x00000000fee00000] (64MB)[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=8[    0.000000] rcu: Preemptible hierarchical RCU implementation.[    0.000000] rcu: RCU event tracing is enabled.[    0.000000] Trampoline variant of Tasks RCU enabled.[    0.000000] Tracing variant of Tasks RCU enabled.[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.[    0.000000] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.[    0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0[    0.000000] Root IRQ handler: gic_handle_irq[    0.000000] GIC: Using split EOI/Deactivate mode[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.[    0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns[    0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns[    0.000122] Console: colour dummy device 80x25[    0.000128] printk: legacy console [tty1] enabled[    0.000487] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=216000)[    0.000498] pid_max: default: 32768 minimum: 301[    0.000571] LSM: initializing lsm=capability[    0.002663] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, vmalloc)[    0.003559] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, vmalloc)[    0.003612] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc)[    0.003647] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, vmalloc)[    0.004643] rcu: Hierarchical SRCU implementation.[    0.004654] rcu: Max phase no-delay instances is 1000.[    0.004732] Timer migration: 1 hierarchy levels; 8 children per group; 0 crossnode level[    0.005257] EFI services will not be available.[    0.005346] smp: Bringing up secondary CPUs ...[    0.005538] Detected PIPT I-cache on CPU1[    0.005586] CPU1: Booted secondary processor 0x0000000100 [0x414fd0b1][    0.005819] Detected PIPT I-cache on CPU2[    0.005858] CPU2: Booted secondary processor 0x0000000200 [0x414fd0b1][    0.006061] Detected PIPT I-cache on CPU3[    0.006096] CPU3: Booted secondary processor 0x0000000300 [0x414fd0b1][    0.006143] smp: Brought up 8 nodes, 4 CPUs[    0.006167] SMP: Total of 4 processors activated.[    0.006171] CPU: All CPU(s) started at EL2[    0.006176] CPU features: detected: 32-bit EL0 Support[    0.006181] CPU features: detected: Data cache clean to the PoU not required for I/D coherence[    0.006187] CPU features: detected: Common not Private translations[    0.006192] CPU features: detected: CRC32 instructions[    0.006199] CPU features: detected: RCpc load-acquire (LDAPR)[    0.006203] CPU features: detected: LSE atomic instructions[    0.006208] CPU features: detected: Privileged Access Never[    0.006213] CPU features: detected: RAS Extension Support[    0.006218] CPU features: detected: Speculative Store Bypassing Safe (SSBS)[    0.006244] alternatives: applying system-wide alternatives[    0.006887] CPU features: detected: Hardware dirty bit management on CPU0-3[    0.007135] Memory: 8048380K/8384512K available (8832K kernel code, 990K rwdata, 2800K rodata, 2048K init, 439K bss, 247440K reserved, 65536K cma-reserved)[    0.007643] devtmpfs: initialized[    0.011872] Enabled cp15_barrier support[    0.011883] Enabled setend support[    0.011944] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns[    0.012000] futex hash table entries: 1024 (order: 4, 65536 bytes, vmalloc)[    0.012597] 2G module region forced by RANDOMIZE_MODULE_REGION_FULL[    0.012603] 0 pages in range for non-PLT usage[    0.012606] 520464 pages in range for PLT usage[    0.012715] pinctrl core: initialized pinctrl subsystem[    0.012960] DMI not present or invalid.[    0.013090] NET: Registered PF_NETLINK/PF_ROUTE protocol family[    0.013605] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations[    0.013677] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations[    0.013796] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations[    0.013820] audit: initializing netlink subsys (disabled)[    0.013929] audit: type=2000 audit(0.012:1): state=initialized audit_enabled=0 res=1[    0.014111] thermal_sys: Registered thermal governor 'step_wise'[    0.014127] cpuidle: using governor menu[    0.014289] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.[    0.014333] ASID allocator initialised with 32768 entries[    0.014703] Serial: AMBA PL011 UART driver[    0.015634] /soc@107c000000/interrupt-controller@7fff9000: Fixed dependency cycle(s) with /soc@107c000000/interrupt-controller@7fff9000[    0.015939] bcm2835-mbox 107c013880.mailbox: mailbox enabled[    0.016199] 107d001000.serial: ttyAMA10 at MMIO 0x107d001000 (irq = 16, base_baud = 0) is a PL011 rev3[    0.016218] printk: legacy console [ttyAMA10] enabled[    1.036266] raspberrypi-firmware soc@107c000000:firmware: Attached to firmware from 2025-09-08T14:51:58, variant start_cd[    1.051288] raspberrypi-firmware soc@107c000000:firmware: Firmware hash is d179f03a00000000000000000000000000000000[    1.070048] bcm2835-dma 1000010000.dma: DMA legacy API manager, dmachans=0x1[    1.077624] iommu: Default domain type: Translated[    1.082471] iommu: DMA domain TLB invalidation policy: strict mode[    1.088877] SCSI subsystem initialized[    1.092702] usbcore: registered new interface driver usbfs[    1.098223] usbcore: registered new interface driver hub[    1.103566] usbcore: registered new device driver usb[    1.109143] vgaarb: loaded[    1.112026] clocksource: Switched to clocksource arch_sys_counter[    1.120683] NET: Registered PF_INET protocol family[    1.125811] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, vmalloc)[    1.136427] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, vmalloc)[    1.145147] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, vmalloc)[    1.153034] TCP established hash table entries: 65536 (order: 7, 524288 bytes, vmalloc)[    1.161408] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, vmalloc)[    1.169956] TCP: Hash tables configured (established 65536 bind 65536)[    1.176644] MPTCP token hash table entries: 8192 (order: 5, 196608 bytes, vmalloc)[    1.184305] UDP hash table entries: 4096 (order: 5, 131072 bytes, vmalloc)[    1.191315] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, vmalloc)[    1.198793] NET: Registered PF_UNIX/PF_LOCAL protocol family[    1.204643] RPC: Registered named UNIX socket transport module.[    1.210593] RPC: Registered udp transport module.[    1.215314] RPC: Registered tcp transport module.[    1.220037] RPC: Registered tcp-with-tls transport module.[    1.225544] RPC: Registered tcp NFSv4.1 backchannel transport module.[    1.232020] PCI: CLS 0 bytes, default 64[    1.236031] Trying to unpack rootfs image as initramfs...[    1.241964] Initialise system trusted keyrings[    1.246688] workingset: timestamp_bits=42 max_order=21 bucket_order=0[    1.253488] NFS: Registering the id_resolver key type[    1.258577] Key type id_resolver registered[    1.262777] Key type id_legacy registered[    1.266817] nfs4filelayout_init: NFSv4 File Layout Driver Registering...[    1.273550] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...[    1.281282] Key type asymmetric registered[    1.285407] Asymmetric key parser 'x509' registered[    1.290342] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)[    1.297845] io scheduler mq-deadline registered[    1.302400] io scheduler kyber registered[    1.306444] io scheduler bfq registered[    1.310797] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d508380, parent irq: 27)[    1.319554] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d508400, parent irq: 28)[    1.328275] irq_brcmstb_l2: registered L2 intc (/soc@107c000000/intc@7d503000, parent irq: 29)[    1.338504] ledtrig-cpu: registered to indicate activity on CPUs[    1.580964] Freeing initrd memory: 16944K[    1.587175] bcm2708_fb soc@107c000000:fb: Unable to determine number of FBs. Disabling driver.[    1.595839] bcm2708_fb soc@107c000000:fb: probe with driver bcm2708_fb failed with error -2[    1.639527] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled[    1.646383] 107d50c000.serial: ttyS0 at MMIO 0x107d50c000 (irq = 31, base_baud = 6000000) is a Broadcom BCM7271 UART[    1.657038] serial serial0: tty port ttyS0 registered[    1.662493] iproc-rng200 107d208000.rng: hwrng registered[    1.667975] vc-mem: phys_addr:0x00000000 mem_base=0x3fc00000 mem_size:0x40000000(1024 MiB)[    1.676605] bcm2712-iommu-cache 1000005b00.iommuc: bcm2712_iommu_cache_probe[    1.686366] brd: module loaded[    1.691065] loop: module loaded[    1.694356] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver[    1.702886] usbcore: registered new interface driver lan78xx[    1.708656] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)[    1.714455] dwc_otg: FIQ enabled[    1.717697] dwc_otg: NAK holdoff enabled[    1.721633] dwc_otg: FIQ split-transaction FSM enabled[    1.726795] Module dwc_common_port init[    1.730816] usbcore: registered new interface driver uas[    1.736170] usbcore: registered new interface driver usb-storage[    1.742291] mousedev: PS/2 mouse device common for all mice[    1.756455] rpi-rtc soc@107c000000:rpi_rtc: registered as rtc0[    1.763864] rpi-rtc soc@107c000000:rpi_rtc: setting system clock to 1970-01-01T00:00:14 UTC (14)[    1.773095] bcm2835-wdt bcm2835-wdt: Poweroff handler already present![    1.779659] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer[    1.788607] sdhci: Secure Digital Host Controller Interface driver[    1.794820] sdhci: Copyright(c) Pierre Ossman[    1.799242] sdhci-pltfm: SDHCI platform and OF driver helper[    1.805028] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....[    1.811515] hid: raw HID events driver (C) Jiri Kosina[    1.816710] usbcore: registered new interface driver usbhid[    1.822307] usbhid: USB HID core driver[    1.826589] hw perfevents: enabled with armv8_cortex_a76 PMU driver, 7 (0,8000003f) counters available[    1.836343] NET: Registered PF_INET6 protocol family[    1.841684] Segment Routing with IPv6[    1.845377] In-situ OAM (IOAM) with IPv6[    1.849339] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver[    1.855467] NET: Registered PF_PACKET protocol family[    1.860570] Key type dns_resolver registered[    1.872156] registered taskstats version 1[    1.876329] Loading compiled-in X.509 certificates[    1.884133] Demotion targets for Node 0: null[    1.888513] Demotion targets for Node 1: null[    1.893540] Demotion targets for Node 2: null[    1.897917] Demotion targets for Node 3: null[    1.902289] Demotion targets for Node 4: null[    1.906661] Demotion targets for Node 5: null[    1.911033] Demotion targets for Node 6: null[    1.915408] Demotion targets for Node 7: null[    1.920038] Key type .fscrypt registered[    1.923973] Key type fscrypt-provisioning registered[    1.930080] brcm-pcie 1000110000.pcie: host bridge /axi/pcie@1000110000 ranges:[    1.937437] brcm-pcie 1000110000.pcie:   No bus range found for /axi/pcie@1000110000, using [bus 00-ff][    1.946894] brcm-pcie 1000110000.pcie:      MEM 0x1b80000000..0x1bffffffff -> 0x0080000000[    1.955205] brcm-pcie 1000110000.pcie:      MEM 0x1800000000..0x1b7fffffff -> 0x0400000000[    1.963521] brcm-pcie 1000110000.pcie:   IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000[    1.971831] brcm-pcie 1000110000.pcie:   IB MEM 0x1000131000..0x1000131fff -> 0xfffffff000[    1.981542] brcm-pcie 1000110000.pcie: PCI host bridge to bus 0001:00[    1.988020] pci_bus 0001:00: root bus resource [bus 00-ff][    1.993534] pci_bus 0001:00: root bus resource [mem 0x1b80000000-0x1bffffffff] (bus address [0x80000000-0xffffffff])[    2.004108] pci_bus 0001:00: root bus resource [mem 0x1800000000-0x1b7fffffff pref] (bus address [0x400000000-0x77fffffff])[    2.015305] pci 0001:00:00.0: [14e4:2712] type 01 class 0x060400 PCIe Root Port[    2.022654] pci 0001:00:00.0: PCI bridge to [bus 00][    2.027641] pci 0001:00:00.0:   bridge window [mem 0x00000000-0x000fffff][    2.034461] pci 0001:00:00.0:   bridge window [mem 0x00000000-0x000fffff 64bit pref][    2.042262] pci 0001:00:00.0: PME# supported from D0 D3hot[    2.048776] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring[    2.400030] brcm-pcie 1000110000.pcie: link down[    2.404705] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01[    2.411356] pci 0001:00:00.0: PCI bridge to [bus 01][    2.416344] pci_bus 0001:00: resource 4 [mem 0x1b80000000-0x1bffffffff][    2.422989] pci_bus 0001:00: resource 5 [mem 0x1800000000-0x1b7fffffff pref][    2.430071] pci 0001:00:00.0: Max Payload Size set to  512/ 512 (was  128), Max Read Rq  512[    2.438674] pcieport 0001:00:00.0: PME: Signaling with IRQ 36[    2.444529] pcieport 0001:00:00.0: AER: enabled with IRQ 36[    2.450243] pci_bus 0001:01: busn_res: [bus 01] is released[    2.455912] pci_bus 0001:00: busn_res: [bus 00-ff] is released[    2.461912] brcm-pcie 1000120000.pcie: host bridge /axi/pcie@1000120000 ranges:[    2.469265] brcm-pcie 1000120000.pcie:   No bus range found for /axi/pcie@1000120000, using [bus 00-ff][    2.478714] brcm-pcie 1000120000.pcie:      MEM 0x1f00000000..0x1ffffffffb -> 0x0000000000[    2.487024] brcm-pcie 1000120000.pcie:      MEM 0x1c00000000..0x1effffffff -> 0x0400000000[    2.495345] brcm-pcie 1000120000.pcie:   IB MEM 0x1f00000000..0x1f003fffff -> 0x0000000000[    2.503657] brcm-pcie 1000120000.pcie:   IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000[    2.511973] brcm-pcie 1000120000.pcie:   IB MEM 0x1000130000..0x1000130fff -> 0xfffffff000[    2.521560] brcm-pcie 1000120000.pcie: PCI host bridge to bus 0002:00[    2.528039] pci_bus 0002:00: root bus resource [bus 00-ff][    2.533564] pci_bus 0002:00: root bus resource [mem 0x1f00000000-0x1ffffffffb] (bus address [0x00000000-0xfffffffb])[    2.544140] pci_bus 0002:00: root bus resource [mem 0x1c00000000-0x1effffffff pref] (bus address [0x400000000-0x6ffffffff])[    2.555334] pci 0002:00:00.0: [14e4:2712] type 01 class 0x060400 PCIe Root Port[    2.562684] pci 0002:00:00.0: PCI bridge to [bus 00][    2.567671] pci 0002:00:00.0:   bridge window [mem 0x1f80000000-0x1fbfffffff][    2.574858] pci 0002:00:00.0: PME# supported from D0 D3hot[    2.581351] pci 0002:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring[    2.692032] brcm-pcie 1000120000.pcie: clkreq-mode set to default[    2.698158] brcm-pcie 1000120000.pcie: link up, 5.0 GT/s PCIe x4 (!SSC)[    2.704822] pci 0002:01:00.0: [1de4:0001] type 00 class 0x020000 PCIe Endpoint[    2.712089] pci 0002:01:00.0: BAR 0 [mem 0xffffc000-0xffffffff][    2.718040] pci 0002:01:00.0: BAR 1 [mem 0xffc00000-0xffffffff][    2.723990] pci 0002:01:00.0: BAR 2 [mem 0xffff0000-0xffffffff][    2.730004] pci 0002:01:00.0: supports D1[    2.734029] pci 0002:01:00.0: PME# supported from D0 D1 D3hot D3cold[    2.748043] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01[    2.754696] pci 0002:00:00.0: bridge window [mem 0x1f00000000-0x1f005fffff]: assigned[    2.762565] pci 0002:01:00.0: BAR 1 [mem 0x1f00000000-0x1f003fffff]: assigned[    2.769736] pci 0002:01:00.0: BAR 2 [mem 0x1f00400000-0x1f0040ffff]: assigned[    2.776906] pci 0002:01:00.0: BAR 0 [mem 0x1f00410000-0x1f00413fff]: assigned[    2.784080] pci 0002:00:00.0: PCI bridge to [bus 01][    2.789077] pci 0002:00:00.0:   bridge window [mem 0x1f00000000-0x1f005fffff][    2.796247] pci_bus 0002:00: resource 4 [mem 0x1f00000000-0x1ffffffffb][    2.802890] pci_bus 0002:00: resource 5 [mem 0x1c00000000-0x1effffffff pref][    2.809971] pci_bus 0002:01: resource 1 [mem 0x1f00000000-0x1f005fffff][    2.816616] pci 0002:00:00.0: Max Payload Size set to  256/ 512 (was  128), Max Read Rq  512[    2.825100] pci 0002:01:00.0: Max Payload Size set to  256/ 256 (was  128), Max Read Rq  512[    2.833655] pcieport 0002:00:00.0: enabling device (0000 -> 0002)[    2.839814] pcieport 0002:00:00.0: PME: Signaling with IRQ 37[    2.845667] pcieport 0002:00:00.0: AER: enabled with IRQ 37[    2.851367] rp1 0002:01:00.0: bar0 len 0x4000, start 0x1f00410000, end 0x1f00413fff, flags, 0x40200[    2.860463] rp1 0002:01:00.0: bar1 len 0x400000, start 0x1f00000000, end 0x1f003fffff, flags, 0x40200[    2.869740] rp1 0002:01:00.0: enabling device (0000 -> 0002)[    2.876602] rp1 0002:01:00.0: chip_id 0x20001927[    2.886636] genirq: irq_chip rp1_irq_chip did not update eff. affinity mask of irq 99[    2.907215] macb 1f00100000.ethernet eth0: Cadence GEM rev 0x00070109 at 0x1f00100000 irq 105 (d8:3a:dd:d4:ff:ec)[    2.918495] dw_axi_dmac_platform 1f00188000.dma: DesignWare AXI DMA Controller, 8 channels[    2.927197] xhci-hcd xhci-hcd.0: xHCI Host Controller[    2.932296] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1[    2.940001] xhci-hcd xhci-hcd.0: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000808000000810[    2.949021] xhci-hcd xhci-hcd.0: irq 130, io mem 0x1f00200000[    2.954873] xhci-hcd xhci-hcd.0: xHCI Host Controller[    2.959950] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2[    2.967209] xhci-hcd xhci-hcd.0: Host supports USB 3.0 SuperSpeed[    2.973393] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12[    2.981703] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1[    2.988965] usb usb1: Product: xHCI Host Controller[    2.993864] usb usb1: Manufacturer: Linux 6.12.42-v8 xhci-hcd[    2.999635] usb usb1: SerialNumber: xhci-hcd.0[    3.004252] hub 1-0:1.0: USB hub found[    3.008044] hub 1-0:1.0: 2 ports detected[    3.012314] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12[    3.020624] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1[    3.027881] usb usb2: Product: xHCI Host Controller[    3.032779] usb usb2: Manufacturer: Linux 6.12.42-v8 xhci-hcd[    3.038566] usb usb2: SerialNumber: xhci-hcd.0[    3.043258] hub 2-0:1.0: USB hub found[    3.047040] hub 2-0:1.0: 1 port detected[    3.051440] xhci-hcd xhci-hcd.1: xHCI Host Controller[    3.056654] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3[    3.064357] xhci-hcd xhci-hcd.1: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000808000000810[    3.073497] xhci-hcd xhci-hcd.1: irq 135, io mem 0x1f00300000[    3.079355] xhci-hcd xhci-hcd.1: xHCI Host Controller[    3.084547] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4[    3.091805] xhci-hcd xhci-hcd.1: Host supports USB 3.0 SuperSpeed[    3.098080] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12[    3.106386] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1[    3.113752] usb usb3: Product: xHCI Host Controller[    3.118653] usb usb3: Manufacturer: Linux 6.12.42-v8 xhci-hcd[    3.124534] usb usb3: SerialNumber: xhci-hcd.1[    3.129132] hub 3-0:1.0: USB hub found[    3.132923] hub 3-0:1.0: 2 ports detected[    3.137250] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12[    3.145558] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1[    3.152950] usb usb4: Product: xHCI Host Controller[    3.157849] usb usb4: Manufacturer: Linux 6.12.42-v8 xhci-hcd[    3.163691] usb usb4: SerialNumber: xhci-hcd.1[    3.168408] hub 4-0:1.0: USB hub found[    3.172298] hub 4-0:1.0: 1 port detected[    3.177622] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774[    3.186337] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_probe: Success[    3.193710] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774[    3.202412] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_probe: Success[    3.209803] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774[    3.218491] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_probe: Success[    3.225608] sdhci-brcmstb 1000fff000.mmc: Got CD GPIO[    3.230994] mmc1: CQHCI version 5.10[    3.231090] mmc0: CQHCI version 5.10[    3.236523] of_cfs_init[    3.240726] of_cfs_init: OK[    3.243591] clk: Disabling unused clocks[    3.257797] PM: genpd: Disabling unused power domains[    3.279281] mmc0: SDHCI controller on 1000fff000.mmc [1000fff000.mmc] using ADMA 64-bit[    3.426575] mmc1: SDHCI controller on 1001100000.mmc [1001100000.mmc] using ADMA 64-bit[    3.435303] Freeing unused kernel memory: 2048K[    3.439903] Run /init as init process[    3.443579]   with arguments:[    3.446554]     /init[    3.448831]   with environment:[    3.451978]     HOME=/[    3.454342]     TERM=linux[    3.465178] mmc1: new ultra high speed DDR50 SDIO card at address 0001[    3.466191] systemd[1]: System time before build time, advancing clock.[    3.488062] systemd[1]: systemd 256.7 running in system mode (-PAM -AUDIT -SELINUX -APPARMOR -IMA -SMACK -SECCOMP -GCRYPT -GNUTLS -OPENSSL -ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD +LIBCRYPTSETUP +LIBCRYPTSETUP_PLUGINS +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 -LZ4 +XZ -ZLIB -ZSTD -BPF_FRAMEWORK -XKBCOMMON -UTMP -SYSVINIT -LIBARCHIVE)[    3.520742] systemd[1]: Detected architecture arm64.Welcome to Buildroot 2024.11.3![    3.532124] systemd[1]: Hostname set to <rpimsg>.[    3.536926] systemd[1]: Initializing machine ID from random generator.[    3.616167] systemd-ssh-generator[132]: Disabling SSH generator logic, since sshd is not installed.[    3.676323] systemd[1]: /etc/systemd/system/getty@tty1.service.d/autologin.conf:3: Ignoring unknown escape sequences: "\$TERM"[    3.697777] systemd[1]: Queued start job for default target Multi-User System.[    3.749050] systemd[1]: Created slice Slice /system/getty.[  OK  ] Created slice Slice /system/getty.[    3.764399] systemd[1]: Created slice Slice /system/modprobe.[  OK  ] Created slice Slice /system/modprobe.[    3.780376] systemd[1]: Created slice Slice /system/serial-getty.[  OK  ] Created slice Slice /system/serial-getty.[    3.796144] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.[  OK  ] Started Dispatch Password Requests to Console Directory Watch.[    3.816120] systemd[1]: Started Forward Password Requests to Wall Directory Watch.[  OK  ] Started Forward Password Requests to Wall Directory Watch.[    3.836080] systemd[1]: Expecting device /dev/ttyAMA10...         Expecting device /dev/ttyAMA10...[    3.852067] systemd[1]: Reached target Local Encrypted Volumes.[  OK  ] Reached target Local Encrypted Volumes.[    3.868076] systemd[1]: Reached target Local Integrity Protected Volumes.[  OK  ] Reached target Local Integrity Protected Volumes.[    3.888093] systemd[1]: Reached target Remote Encrypted Volumes.[  OK  ] Reached target Remote Encrypted Volumes.[    3.904067] systemd[1]: Reached target Remote File Systems.[  OK  ] Reached target Remote File Systems.[    3.920070] systemd[1]: Reached target Remote Verity Protected Volumes.[  OK  ] Reached target Remote Verity Protected Volumes.[    3.940068] systemd[1]: Reached target Slice Units.[  OK  ] Reached target Slice Units.[    3.952078] systemd[1]: Reached target Swaps.[  OK  ] Reached target Swaps.[    3.964095] systemd[1]: Reached target Local Verity Protected Volumes.[  OK  ] Reached target Local Verity Protected Volumes.[    3.984177] systemd[1]: Listening on Device-mapper event daemon FIFOs.[  OK  ] Listening on Device-mapper event daemon FIFOs.[    4.005359] systemd[1]: Listening on Credential Encryption/Decryption.[  OK  ] Listening on Credential Encryption/Decryption.[    4.024347] systemd[1]: Listening on Journal Audit Socket.[  OK  ] Listening on Journal Audit Socket.[    4.040191] systemd[1]: Listening on Journal Socket (/dev/log).[  OK  ] Listening on Journal Socket (/dev/log).[    4.056188] systemd[1]: Listening on Journal Sockets.[  OK  ] Listening on Journal Sockets.[    4.072231] systemd[1]: Listening on Network Service Netlink Socket.[  OK  ] Listening on Network Service Netlink Socket.[    4.088196] systemd[1]: Listening on udev Control Socket.[  OK  ] Listening on udev Control Socket.[    4.104154] systemd[1]: Listening on udev Kernel Socket.[  OK  ] Listening on udev Kernel Socket.[    4.120230] systemd[1]: Huge Pages File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages).[    4.133990] systemd[1]: Mounting POSIX Message Queue File System...         Mounting POSIX [    4.141407] systemd[1]: Mounting Kernel Debug File System...Message Queue File System...         Mounting Kernel[    4.156277] systemd[1]: Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing). Debug File System...[    4.188728] systemd[1]: Mounting Temporary Directory /tmp...         Mounting Tempor[    4.195553] systemd[1]: Starting Availability of block devices...ary Directory /tmp...         Starting Availa[    4.209241] systemd[1]: Starting Create List of Static Device Nodes...bility of block devices...         Starting Create[    4.225102] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling... List of Static Device Nodes...         Starting Monito[    4.245219] systemd[1]: Starting Load Kernel Module configfs...ring of LVM2 mirror…ing dmeventd or progress polling...         Starting Load K[    4.261223] systemd[1]: Starting Load Kernel Module fuse...ernel Module configfs...[    4.273889] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev         Starting Load K[    4.288242] systemd[1]: File System Check on Root Device was skipped because of an unmet condition check (ConditionPathIsReadWrite=!/).ernel Module fuse...[    4.341796] systemd[1]: Starting Journal Service...         Starting Journa[    4.347106] systemd[1]: Load Kernel Modules was skipped because no trigger condition checks were met.l Service...[    4.359115] fuse: init (API version 7.41)[    4.360022] systemd[1]: Starting Generate network units from Kernel command line...         Starting Genera[    4.381177] systemd[1]: Starting Remount Root and Kernel File Systems...te network units from Kernel command line...[    4.393690] systemd-journald[148]: Collecting audit messages is enabled.         Starting Remoun[    4.409211] systemd[1]: Starting Apply Kernel Variables...t Root and Kernel File Systems...         Starting Apply [    4.421265] systemd[1]: Starting Load udev Rules from Credentials...Kernel Variables...         Starting Load udev Rules from Credentials...[    4.449067] systemd[1]: Starting Coldplug All udev Devices...         Starting Coldplug All udev Devices...[    4.458022] systemd[1]: Started Journal Service.[  OK  ] Started Journal Service.[  OK  ] Mounted POSIX Message Queue File System.[  OK  ] Mounted Kernel Debug File System.[  OK  ] Mounted Temporary Directory /tmp.[  OK  ] Finished Availability of block devices.[  OK  ] Finished Create List of Static Device Nodes.[  OK  ] Finished Monitoring of LVM2 mirror…using dmeventd or progress polling.[  OK  ] Finished Load Kernel Module configfs.[  OK  ] Finished Load Kernel Module fuse.[  OK  ] Finished Generate network units from Kernel command line.[  OK  ] Finished Remount Root and Kernel File Systems.[  OK  ] Finished Apply Kernel Variables.[  OK  ] Finished Load udev Rules from Credentials.[  OK  ] Finished Coldplug All udev Devices.[  OK  ] Reached target Preparation for Network.         Mounting FUSE Control File System...         Mounting Kernel Configuration File System...         Starting Flush Journal to Persistent Storage...         Starting Create Static Device N[    4.695866] systemd-journald[148]: Received client request to flush runtime journal.odes in /dev gracefully...[  OK  ] Mounted FUSE Control File System.[  OK  ] Mounted Kernel Configuration File System.[  OK  ] Finished Flush Journal to Persistent Storage.[  OK  ] Finished Create Static Device Nodes in /dev gracefully.         Starting Create Static Device Nodes in /dev...[  OK  ] Finished Create Static Device Nodes in /dev.[  OK  ] Reached target Preparation for Local File Systems.[  OK  ] Reached target Local File Systems.         Starting Create System Files and Directories...[    4.868638] audit: type=1334 audit(1728402151.399:2): prog-id=6 op=LOAD[    4.875302] audit: type=1334 audit(1728402151.403:3): prog-id=7 op=LOAD         Starting Rule-based Manager for Device Events and Files...         Starting Update is Completed...[  OK  ] Finished Update is Completed.[  OK  ] Finished Create System Files and Directories.[  OK  ] Started Rule-based Manager for Device Events and Files.[    4.982404] macb 1f00100000.ethernet end0: renamed from eth0[    5.004460] audit: type=1334 audit(1728402151.535:4): prog-id=8 op=LOAD         Starting Network Configuration...[    5.021533] audit: type=1334 audit(1728402151.551:5): prog-id=9 op=LOAD         Starting Network Name Resolution...[    5.041956] rpi-gpiomem 107d508500.gpiomem: window base 0x107d508500 size 0x00000040[    5.042009] audit: type=1334 audit(1728402151.571:6): prog-id=10 op=LOAD         Starting Networ[    5.056625] rpi-gpiomem 107d508500.gpiomem: initialised 1 regions as /dev/gpiomem1k Time Synchronization...[    5.067251] rp1-firmware rp1_firmware: RP1 Firmware version eb39cfd516f8c90628aa9d91f52370aade5d0a55[    5.067870] rpi-gpiomem 107d517c00.gpiomem: window base 0x107d517c00 size 0x00000040[    5.087064] rpi-gpiomem 107d517c00.gpiomem: initialised 1 regions as /dev/gpiomem2[    5.091862] dwc2 1000480000.usb: supply vusb_d not found, using dummy regulator[    5.094735] rp1-pio 1f00178000.pio: Created instance as pio0[    5.102095] rpi-gpiomem 107d504100.gpiomem: window base 0x107d504100 size 0x00000020[    5.102144] dwc2 1000480000.usb: supply vusb_a not found, using dummy regulator[  OK  ] Found device /dev/tt[    5.125360] rpi-gpiomem 107d504100.gpiomem: initialised 1 regions as /dev/gpiomem3yAMA10.[    5.136108] rpi-gpiomem 107d510700.gpiomem: window base 0x107d510700 size 0x00000020[    5.145101] rpi-gpiomem 107d510700.gpiomem: initialised 1 regions as /dev/gpiomem4[    5.154976] rpi-gpiomem 1f000d0000.gpiomem: window base 0x1f000d0000 size 0x00030000[    5.163885] rpi-gpiomem 1f000d0000.gpiomem: initialised 1 regions as /dev/gpiomem0[    5.204434] dwc2 1000480000.usb: EPs: 8, dedicated fifos, 4080 entries in SPRAM[  OK  ] Started Network Configuration.[    5.228649] macb 1f00100000.ethernet end0: PHY [1f00100000.ethernet-ffffffff:01] driver [Broadcom BCM54213PE] (irq=POLL)[    5.240166] macb 1f00100000.ethernet end0: configuring for phy/rgmii-id link mode[  OK  ] Started Network Time Synchronization.[  OK  ] Started Network Name Resolution.[  OK  ] Reached target Network.[  OK  ] Reached target Host and Network Name Lookups.[  OK  ] Reached target System Time Set.[  OK  ] Reached target Hardware activated USB gadget.         Starting Enable Persistent Storage in systemd-networkd...         Starting Virtual Console Setup...[  OK  ] Finished Enable Persistent Storage in systemd-networkd.[  OK  ] Finished Virtual Console Setup.[  OK  ] Reached target System Initialization.[  OK  ] Started lvm-devices-import to create system.devices.[  OK  ] Started Discard unused filesystem blocks once a week.[  OK  ] Started Daily Cleanup of Temporary Directories.[  OK  ] Reached target Path Units.[  OK  ] Reached target Timer Units.[  OK  ] Listening on D-Bus System Message Bus Socket.[  OK  ] Listening on Hostname Service Socket.[  OK  ] Reached target Socket Units.[  OK  ] Reached target Basic System.         Starting D-Bus System Message Bus...         Starting DHCP client...[  OK  ] Started Getty on tty1.         Starting Create lvm system.devices...[  OK  ] Started Serial Getty on ttyAMA10.[  OK  ] Reached target Login Prompts.         Starting Mass storage gadget...[  OK  ] Started D-Bus System Message Bus.[  OK  ] Started DHCP client.[  OK  ] Finished Create lvm system.devices.[    5.205820] configure-gadgets[[    5.654172] dwc2 1000480000.usb: bound driver configfs-gadget.rpimsg253]: Found UDC 1000480000.usb[  OK  ] Started Serial Getty on ttyGS0.[    5.244311] configure-gadgets[253]: Mass storage gadget init complete - 1000480000.usb[  OK  ] Finished Mass storage gadget.[  OK  ] Reached target Multi-User System.[    5.748010] dwc2 1000480000.usb: new device is high-speedRaspberry Pi 64-bit Mass Storage Gadgetrpimsg login: root (automatic login)# [    5.870008] dwc2 1000480000.usb: new device is high-speed[    6.232736] dwc2 1000480000.usb: new device is high-speed[    6.329240] dwc2 1000480000.usb: new address 6

Code:

Raspberry Pi 64-bit Mass Storage Gadgetrpimsg login: root (automatic login)# [    5.870008] dwc2 1000480000.usb: new device is high-speed[    6.232736] dwc2 1000480000.usb: new device is high-speed[    6.329240] dwc2 1000480000.usb: new address 6hh-bash: hh: command not found# # # # exitlogoutRaspberry Pi 64-bit Mass Storage Gadgetrpimsg login: root (automatic login)# q-bash: q: command not found# ls # # pwd/root# ls -latotal 4drwx------    3 root     root             0 Oct  8 15:51 .drwxr-xr-x   17 root     root             0 Aug 21  2025 ..-rw-------    1 root     root             8 Oct  8 15:51 .bash_historydrwx------    2 root     root             0 Aug 21  2025 .ssh# usname -a-bash: usname: command not found# uname -aLinux rpimsg 6.12.42-v8 #1 SMP PREEMPT Thu Aug 21 12:06:01 BST 2025 aarch64 GNU/Linux# cat /etc/os-releaseNAME=BuildrootVERSION=2024.11.3-22-g6f324179efID=buildrootVERSION_ID=2024.11.3PRETTY_NAME="Buildroot 2024.11.3"# ls /devautofs           mqueue           tty15            tty5block            null             tty16            tty50btrfs-control    pio0             tty17            tty51bus              port             tty18            tty52char             ptmx             tty19            tty53console          pts              tty2             tty54cpu_dma_latency  ram0             tty20            tty55cuse             ram1             tty21            tty56disk             ram10            tty22            tty57dma_heap         ram11            tty23            tty58fd               ram12            tty24            tty59full             ram13            tty25            tty6fuse             ram14            tty26            tty60gpiochip0        ram15            tty27            tty61gpiochip10       ram2             tty28            tty62gpiochip11       ram3             tty29            tty63gpiochip12       ram4             tty3             tty7gpiochip13       ram5             tty30            tty8gpiomem0         ram6             tty31            tty9gpiomem1         ram7             tty32            ttyAMA10gpiomem2         ram8             tty33            ttyGS0gpiomem3         ram9             tty34            ttyprintkgpiomem4         random           tty35            uhidhwrng            rtc              tty36            urandominput            rtc0             tty37            vc-memkmsg             shm              tty38            vciolog              spidev10.0       tty39            vcsloop-control     stderr           tty4             vcs1loop0            stdin            tty40            vcsaloop1            stdout           tty41            vcsa1loop2            tty              tty42            vcsuloop3            tty0             tty43            vcsu1loop4            tty1             tty44            vga_arbiterloop5            tty10            tty45            watchdogloop6            tty11            tty46            watchdog0loop7            tty12            tty47            zeromapper           tty13            tty48mem              tty14            tty49# ps auxPID   USER     COMMAND    1 root     {systemd} /sbin/init    2 root     [kthreadd]    3 root     [pool_workqueue_]    4 root     [kworker/R-kvfre]    5 root     [kworker/R-rcu_g]    6 root     [kworker/R-sync_]    7 root     [kworker/R-slub_]    8 root     [kworker/R-netns]   10 root     [kworker/0:0H-ev]   12 root     [kworker/u16:0-i]   13 root     [kworker/R-mm_pe]   14 root     [rcu_tasks_kthre]   15 root     [rcu_tasks_trace]   16 root     [ksoftirqd/0]   17 root     [rcu_preempt]   18 root     [rcu_exp_par_gp_]   19 root     [rcu_exp_gp_kthr]   20 root     [migration/0]   21 root     [cpuhp/0]   22 root     [cpuhp/1]   23 root     [migration/1]   24 root     [ksoftirqd/1]   26 root     [kworker/1:0H-ev]   27 root     [cpuhp/2]   28 root     [migration/2]   29 root     [ksoftirqd/2]   31 root     [kworker/2:0H-ev]   32 root     [cpuhp/3]   33 root     [migration/3]   34 root     [ksoftirqd/3]   36 root     [kworker/3:0H-ev]   37 root     [kworker/u17:0-e]   38 root     [kworker/u18:0-e]   40 root     [kworker/u20:0-e]   41 root     [kdevtmpfs]   42 root     [kworker/R-inet_]   43 root     [kauditd]   44 root     [khungtaskd]   45 root     [oom_reaper]   46 root     [kworker/R-write]   47 root     [kcompactd0]   48 root     [kcompactd1]   49 root     [kcompactd2]   50 root     [kcompactd3]   51 root     [kcompactd4]   52 root     [kcompactd5]   53 root     [kcompactd6]   54 root     [kcompactd7]   55 root     [kworker/R-kinte]   56 root     [kworker/R-kbloc]   57 root     [kworker/R-blkcg]   58 root     [kworker/u17:1-e]   59 root     [kworker/u17:2-e]   60 root     [watchdogd]   61 root     [kworker/1:1-mm_]   62 root     [kworker/0:1H]   63 root     [kworker/R-rpcio]   64 root     [kworker/R-xprti]   65 root     [kswapd0]   66 root     [kswapd1]   67 root     [kswapd2]   68 root     [kswapd3]   69 root     [kswapd4]   70 root     [kswapd5]   71 root     [kswapd6]   72 root     [kswapd7]   73 root     [kworker/R-nfsio]   74 root     [kworker/3:1-eve]   76 root     [kworker/R-kthro]   78 root     [kworker/2:3-mm_]   79 root     [kworker/2:4-mm_]   80 root     [kworker/u19:1-e]   82 root     [hwrng]   83 root     [kworker/R-nvme-]   84 root     [kworker/R-nvme-]   85 root     [kworker/R-nvme-]   86 root     [kworker/R-DWC N]   87 root     [kworker/R-uas]   88 root     [kworker/R-mld]   89 root     [kworker/2:1H]   90 root     [kworker/R-ipv6_]   91 root     [kworker/u16:1-i]   92 root     [kworker/u21:0]   93 root     [kworker/u22:0]   94 root     [kworker/u23:0]   95 root     [kworker/u24:0]   96 root     [kworker/u25:0]   98 root     [kworker/u19:3-k]  100 root     [irq/37-aerdrv]  105 root     [kworker/0:5-pm]  108 root     [kworker/R-sdhci]  109 root     [kworker/u18:1-e]  110 root     [irq/161-mmc1]  114 root     [kworker/R-sdhci]  115 root     [irq/160-mmc0]  116 root     [kworker/1:3-mm_]  120 root     [kworker/1:1H]  122 root     [kworker/u20:1]  140 root     [kworker/3:1H]  148 root     /usr/lib/systemd/systemd-journald  150 root     [kworker/3:2-eve]  188 root     /usr/lib/systemd/systemd-udevd  218 systemd- /usr/lib/systemd/systemd-networkd  219 systemd- /usr/lib/systemd/systemd-resolved  220 systemd- /usr/lib/systemd/systemd-timesyncd  221 root     [spi10]  234 dbus     /usr/bin/dbus-daemon --system --address=systemd: --nofork --nopi  236 root     -bash  238 dhcpcd   dhcpcd: [manager] [ip4] [ip6]  239 root     dhcpcd: [privileged proxy]  240 dhcpcd   dhcpcd: [network proxy]  241 dhcpcd   dhcpcd: [control proxy]  272 root     -bash  275 root     [kworker/u20:2]  285 root     [kworker/u18:2-e]  286 root     [kworker/0:0-pm]  287 root     [kworker/3:0-eve]  288 root     -bash  292 root     [kworker/1:0-mm_]  299 root     ps aux# df -hFilesystem                Size      Used Available Use% Mounted ondevtmpfs                  3.8G         0      3.8G   0% /devtmpfs                     3.9G         0      3.9G   0% /dev/shmtmpfs                     1.6G    620.0K      1.6G   0% /runtmpfs                     3.9G         0      3.9G   0% /tmptmpfs                     1.0M         0      1.0M   0% /run/credentials/systemd-journald.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/systemd-network-generator.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/systemd-sysctl.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/systemd-udev-load-credentials.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/systemd-tmpfiles-setup-dev-early.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/systemd-tmpfiles-setup-dev.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/systemd-tmpfiles-setup.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/systemd-resolved.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/systemd-networkd.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/systemd-vconsole-setup.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/serial-getty@ttyGS0.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/getty@tty1.servicetmpfs                     1.0M         0      1.0M   0% /run/credentials/serial-getty@ttyAMA10.service